loadingimg

Wczytuję dane...
PIC-KIT3
Olimex
Poinformuj mnie gdy produkt będzie dostępny

Producent: Olimex

  • Opis produktu

PIC-KIT3 is a low cost programmer/debugger. With its 55 x 55 mm (2.16 x 2.16") dimensions and only 30 grams of weight (excluding the ICSP cable and packing). This little device fits your pocket and is very convenient to carry around when working in field. The PIC-KIT3 is a complete replacement of the Microchip's original PICkit3 and with it you can do everything you could do with the original PICkit3.


FEATURES

  • USB (Full Speed 2 M bits/s) interface to host PC
  • Real-time background debugging
  • MPLAB and MPLAB X compatible (latest release available for free download from Microchip's web site)
  • Built in over-voltage/short circuit monitor
  • Firmware upgradeable from PC
  • Supports low voltage to 2.0 volts. (2.0 to 6.0 range)
  • Diagnostic bi-color LED (Busy, Error)
  • External power jack (6-12VDC) for standalone programming
  • Programmer-to-go function
  • Reading/Writing memory space and EEDATA areas of target microcontroller
  • Programs configuration bits
  • Can erase program memory space with verification
  • Peripheral freeze-on-halt stops timers at breakpoints


HARDWARE

PIC ICSP connector(top view)


SOFTWARE

MPLAB-IDE - you can download the latest version from Microchip's web site.


FAQ

  • What USB cable do I need?
  • You should have a USB type A-B cable to connect to a PC. All PC USB hosts have a USB-A connector while the PIC-KIT3 has a USB-B connector so the cable should be a USB A-to-B type. Note that such a cable is not included in the package.
  • What should I know when connecting the PIC-KIT3 to a target board?
  • It's very important that your target PIC MCLR is not connected directly to the VCC!
    During programming/debugging MCLR goes as high as 13VDC and if your target MCLR is connected directly to the target VCC, you will blow either the PIC-KIT3 or the target board. Always use a 10K pullup resistor from MCLR to VCC.
  • What are the LEDS for?
  • There are two LEDS – one yellow LED named ACTIVE and one double-color LED named STAT (red/green colors). The yellow LED shows USB activity – e.g. when the device is connected to the USB properly; when you are powering the board from an external source via the power jack this LED would blink. The STAT LED shows RED color when you are connected to MPLAB or the image inside the EEPROM is ready for operation. When there is programming data is transferred, the double LED should blink in an orange color (red and green).
  • Hello, I pressed the "programmer-to-go" button and my PIC32 died. What burned my chip?
  • Do not use the "programmer-to-go" button when there is no image in the OLIMEX PIC-KIT3 or MICROCHIP PIC-KIT3 because that might put your microcontroller in an irrecoverable state. We have tested the mentioned scenario and we can confirm that it destroys the PIC32 chips (using both our and the original Microchip PICKIT3). We don't take responsibility if you break your chip that way. For more info check the following: www.microchip.com/forums/m635420.aspx.
Polecamy

PIC-MCP-USB

 

PIC-ICD2-POCKET

 

PIC-PG1

 

PIC-ICSP

 
PIC-MCP-USBPIC-ICD2-POCKETPIC-PG1PIC-ICSP
Poinformuj mnie gdy produkt będzie dostępny
148,04 PLN*
*cena netto, bez podatku VAT
Poinformuj mnie gdy produkt będzie dostępny
109,97 PLN*
*cena netto, bez podatku VAT
Poinformuj mnie gdy produkt będzie dostępny
42,30 PLN*
*cena netto, bez podatku VAT
Poinformuj mnie gdy produkt będzie dostępny
12,48 PLN*
*cena netto, bez podatku VAT
Dodaj: szt.
do koszyka
Dodaj: szt.
do koszyka
Dodaj: szt.
do koszyka
Dodaj: szt.
do koszyka